®Safe & SoundTM Video and audio monitorUser’s manualw w w.v te c h p h o nes .c om Models: VM321/VM321-2BC
4Getting startedBaby unit installation optionsThe baby unit is ready for tabletop use. Use the provided wall mount if you want to mount it on a wall.
5Getting startedBaby unit installation options (continued)Align the wall mount and screws with the holes in the wall as shown. Make sure to attach the
6Getting startedBundle the power cord neatly with the self-adhesive strap. Make sure to keep the power adapter cord away from children’s reach.5.Baby
7Getting startedOption 2: Use this method so that you can relocate the baby unit with the wall mount easily.Place the wall mount on a wall and then us
8Getting startedBaby unit installation options (continued)Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws ar
9Getting startedBaby unit installation options (continued)Bundle the power cord neatly with the self-adhesive strap. Make sure to keep the power adapt
10Getting startedParent unit battery installationYou can power up the parent unit by connecting it to AC power or to the rechargeable battery provided
11Getting startedParent unit battery installation (continued)To replace the battery, press down on the large tab of the battery and pull it out of the
12Getting startedParent unit installationInstall the parent unit as shown below.Make sure that the power outlet is not controlled by a wall switch. Bu
13Getting startedParent unit battery chargingOnce you have installed the parent unit (see page 12) and its battery (see page 10), press for 2 second
Congratulationson purchasing your new VTech product. Before using this product, please read Important safety instructions on pages iii-iv of this manu
14Getting startedBaby unit overview51234612 13 14151678910111 _ Camera2 _ Infrared LEDsBackup light for night vision (page 29).3 _ (On/off)Press and
15Baby unit lightsGetting started (On/off)On in red when the baby unit is powered by batteries.On in green when the baby unit is powered by AC power.
16Parent unit overview451231210116 7 89Getting started1 _ (On/off)Press and hold to turn on or off (page 30).2 _ (Zoom)While viewing in single-CAM m
17Getting startedParent unit lightsLINKOn when strong signal strength is detected between the parent unit and the selected baby unit.Flashes when the
18Getting startedParent unit display screen iconsConnection status- displays when strong signal strength is detected between the baby unit and the p
19Getting startedPositioning and operating rangePosition the video and audio monitorPlace the parent unit within the operating range (see below) of th
20Getting startedTest your video and audio monitor before useIt is important to test the video and audio monitor when it is installed initially, and a
21Parent unit settingsUsing the menuTo enter the parent unit menu:Press MENU/SELECT when the parent unit is not in use.Press or until the desired
Parent unit settings22Alert toneLow battery tone alertYou can set whether the parent unit beeps whenever the parent unit or the baby unit operates in
Parent unit settings23SensitivityYou can use the parent unit to change the sound sensitivity level of the baby units from Level 1 to Level 5 (Maximum)
Product introductionVM321 is a video and audio monitor which consists of one parent unit (VM321 PU) and one baby unit (VM321 BU).VM321-2 is a video a
Parent unit settings24TemperatureMinimum temperatureYou can set the desired minimum room temperature of the baby unit. The minimum temperature can be
Parent unit settings25Temperature (continued)Temperature alertYou can set whether the parent unit beeps whenever the temperature is out of the preset
Parent unit settings26VibrationYou can set the parent unit to vibrate once whenever there is any sound detected from the baby units after 20 seconds o
Parent unit settings27LCD brightnessYou can change the brightness of the parent unit screen from Level 1 to Level 5. The LCD brightness is preset to L
Parent unit settings28Pair/unpair CAM (continued)Unpair CAMMake sure you power on the baby unit and the parent unit before unpairing the baby unit.To
29Baby unit operationPower on or off the baby unitPress and hold for 2 seconds to turn on the baby unit. The light turns on.Press and hold for 2
30Power on or off the parent unitPress and hold for 2 seconds to turn on the parent unit. The display screen turns on.Press and hold for 2 seconds
31ViewYou can change the screen to view images from different baby units, or you can turn off the screen.To view different baby units while in CAM X:P
32Battery low at CAM #When the baby unit is powered by batteries, the stated baby unit batteries need to be changed. It will be powered off after 30 s
33AppendixParent unit batteryIt takes up to 12 hours for the battery to be fully charged. The standby time varies depending on the sensitivity level y
iiiImportant safety instructionsWhen using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shoc
34AppendixTroubleshootingIf you have difficulty with your video and audio monitor, please try the suggestions below. For customer service, visit our we
35AppendixTroubleshooting (continued)The parent unit plays any sounds from the baby unit and I think it is too noisy.You may have set the sensitivity
36AppendixTroubleshooting (continued)The battery does not charge in the parent unit or the parent unit battery does not accept charge.Make sure the ba
37AppendixTroubleshooting (continued)The link between the baby unit and the parent unit is lost every now and then, and I’m experiencing sound interru
38AppendixOperating rangeThis product operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this baby unit
39AppendixThe RBRC® sealThe RBRC® seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an indust
40AppendixFCC and IC regulationsFCC Part 15This equipment has been tested and found to comply with the requirements for a Class B digital device unde
41AppendixCalifornia Energy Commission battery charging testing instructionsThis telephone is set up to comply with the energy-conserving standards ri
42AppendixFor cETL compliance onlyMesures de sécurité importantesLorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures
43AppendixFor cETL compliance only (continued)16. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aé
ivImportant safety instructions (continued)You should test the sound reception every time you turn on the units or move one of the components.Periodic
44AppendixFor cETL compliance only (continued)6. D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et au
45AppendixLimited warrantyWhat does this limited warranty cover?The manufacturer of this VTech Product warrants to the holder of a valid proof of purc
46AppendixHow do you get warranty service?To obtain warranty service in the United States of America, visit www.vtechphones.com or call 1 (800) 595-9
47AppendixFrequency control Crystal controlled PLL synthesizerTransmit frequency Baby unit: 2402 - 2478.5 MHzParent unit: 2402 -2478.5 MHzChannels 52L
48IndexAAdd a baby unit 27Alert 22, 25Alert tone 22Audio settings 19BBaby unit battery installation 2Baby unit installation 3Baby unit installat
49IndexSSafety instructions iii–ivScreen icons 18Screen messages 32Self-adhesive strap 3, 12Sensitivity 23Settings 21–28Single-CAM mode 21Sound
VTech Communications, Inc.A member of THE VTECH GROUP OF COMPANIES.VTech is the registered trademark of VTech Holdings Limited.Specifications are subj
vTable of contentsGetting started ...1Parts checklist ... 1Baby unit battery installation ..
1Important informationParts checklistCheck to make sure the package contains the following items. Save your sales receipt and original packaging in t
2Getting startedBaby unit battery installationYou can power up the baby unit by connecting it to AC power or to four AA alkaline batteries. Even if th
3Getting startedBaby unit installationInstall the baby unit as shown below.Make sure that the power outlet is not controlled by a wall switch. Bundle
Kommentare zu diesen Handbüchern